Mold colonies in crawl spaces originate at ground level and migrate upward through your home's air supply. JCB Waterproofing and Construction installs certified encapsulation systems that cut off moisture at the source.
What makes our encapsulation installs last decades, not years.
We install 20-mil reinforced polyethylene vapor barriers -- not the thin 6-mil sheeting that degrades within a few years under crawl space conditions.
We seal every penetration -- pipes, posts, and support columns -- individually so the barrier is continuous with no gaps that allow moisture to bypass the system.
Sealed crawl spaces consistently show measurable reduction in heating and cooling costs because conditioned air is no longer exchanged with the unconditioned crawl space below.
Protecting the wood structure of your home from moisture is the most cost-effective maintenance you can invest in, and crawl space encapsulation is the most efficient way to accomplish it.
Crawl space encapsulation is the process of sealing a home's crawl space against outside air and ground moisture by installing a continuous vapor barrier on the floor and walls, sealing all vents and penetrations, and managing the internal humidity of the sealed space with a dedicated dehumidifier or conditioned air supply. The result is a semi-conditioned space that behaves like a dry indoor environment rather than an extension of the outside soil -- eliminating the ground moisture evaporation that is the primary driver of crawl space mold and wood rot. In Rockaway, NJ, where soil moisture conditions fluctuate significantly with the seasons, encapsulation provides consistent protection year-round that passive venting strategies cannot match.
The vapor barrier is the physical core of the encapsulation system. Mil thickness matters significantly in this application: 6-mil poly is standard for short-term vapor retarders in above-grade construction, but crawl space conditions include foot traffic during inspections and maintenance, contact with rough aggregate and irregular soil surfaces, rodent activity, and exposure to moisture for decades. We specify a minimum 20-mil reinforced poly with a ripstop layer that resists puncture from debris and maintains its vapor transmission rating even if the surface is scuffed or walked on. The barrier is cut and fitted to the exact dimensions of each crawl space section, with all wall terminations run up to the rim joist and sealed with a waterproof tape rated for that adhesion surface.
HVAC performance in homes with encapsulated crawl spaces improves because the humidity load on the air conditioning system is reduced. In a vented crawl space, humid outside air is drawn under the house, rises through the subfloor into the living space, and must be removed by the air conditioning system. This hidden moisture load causes air conditioners to run longer, increases compressor wear, and reduces the effective cooling capacity of the system. After encapsulation, the crawl space humidity is maintained by a rated standalone dehumidifier that handles only the manageable internal moisture load rather than an endless supply from outside air.
Mold remediation is frequently required in conjunction with encapsulation when visible mold colonies are already established on floor joists, subfloor sheathing, or HVAC components in the crawl space. We assess mold extent as part of every inspection and provide a remediation plan that addresses existing growth before the encapsulation barrier is installed. Installing a vapor barrier over active mold does not eliminate it -- the mold must be treated first to prevent it from continuing to develop and produce airborne spores that migrate into the living space. Our remediation process uses EPA-registered fungicidal treatments applied to all affected wood surfaces, followed by a borate-based preservative application to inhibit future growth.
Six crawl space services that address every moisture source under your Rockaway home.
We cut and fit barrier material to every section of your crawl space, including around posts, piers, and columns, so no ground surface is left exposed to vapor evaporation.
Rated standalone crawl space dehumidifiers installed with gravity drain or condensate pump, sized to the cubic footage of your specific crawl space and set to maintain safe humidity levels year-round.
Existing foundation vents are sealed with rigid foam insulation cut to size and adhered with spray foam to eliminate the primary pathway for outside humid air to enter the crawl space.
When visible mold colonies are present on floor joists, sheathing, or structural framing, we treat affected surfaces with EPA-registered fungicidal solutions before installing the vapor barrier.
Drainage channels are integrated under the vapor barrier perimeter, routing water to a sump pit with a submersible pump sized for your drainage area.
We install weatherstripping and rigid foam panel inserts on all access points sized to provide an airtight fit that maintains the pressure balance of the sealed crawl space.
We enter the crawl space and conduct a systematic inspection of all floor and wall surfaces, document moisture meter readings at multiple locations, photograph all floor joist and beam conditions, and identify every source of water or moisture entry before recommending any course of action.
Where mold remediation is needed, we complete EPA-registered fungicidal treatment and borate application before any encapsulation materials are installed, ensuring no active mold is sealed under the barrier.
Foundation vents are sealed with rigid foam insulation and spray foam adhesive, and the crawl space access hatch is fitted with an insulating door seal panel.
A rated crawl space dehumidifier is installed, connected to gravity drain or a condensate pump, and set to the target humidity level for your Rockaway, NJ climate before we complete the project.
Our floor joists were showing early decay when JCB Waterproofing and Construction inspected. They remediated the mold, sealed the entire crawl space, and installed a dehumidifier -- a year later the wood moisture readings are in the safe range and the floors feel solid again.
JCB Waterproofing and Construction did a full encapsulation in one day and left the crawl space cleaner than it was when they arrived. The dehumidifier they installed has not required any maintenance beyond emptying the drip tray.
I got four quotes and JCB Waterproofing and Construction was the only company that gave me a written spec listing the mil thickness of the poly they were installing. That transparency is why I chose them and their work backed it up completely.
Take the first step toward a healthier, drier home. Contact JCB Waterproofing and Construction for a same-day crawl space inspection.
Call +1-866-476-1348 Now